Black Anodized Aluminum Heat Sink

This is a standard 12mm diameter laser diode module and lens focusing ring. Fits 5.6mm diameter diodes and 9mm lens assemblies. Nickel-plated brass construction.

MADE IN USA. This is a solid copper 12mm diameter diode module, precision machined to the same dimensions as "standard" nickel-plated brass modules, including our P/N SL-DMFR1. Fits 5.6mm diameter diodes and 9mm lens assemblies. The copper alloy used in this module has a thermal conductivity of 355 W/m-k which is over 3 times that of...

DANGER: APPROPRIATE LASER SAFETY GOGGLES MUST BE WORN WHEN OPERATING THIS DIODE! RISK OF INSTANTANEOUS SEVERE EYE DAMAGE OR BLINDNESS! This is a 405nm BDR-S06J 12X diode pressed into a standard diode module and includes a standard focusing ring (extended focusing ring optional). Typical output power is 500 +/- 50mW with a standard 3-element AR...

DANGER: APPROPRIATE LASER SAFETY GOGGLES MUST BE WORN WHEN OPERATING THIS DIODE! RISK OF INSTANTANEOUS SEVERE EYE DAMAGE OR BLINDNESS! A 445nm diode pressed into an AixiZ module, packaged along with an AR coated 445nm glass lens and lens focusing ring. Diodes are fully installed into the module using a diode press for maximum heat transfer during...

DANGER: APPROPRIATE LASER SAFETY GOGGLES MUST BE WORN WHEN OPERATING THIS DIODE! RISK OF INSTANTANEOUS SEVERE EYE DAMAGE OR BLINDNESS! A 5.6mm diameter 445nm wavelength M140 diode. These diodes can produce from less than 1,000mW, to 2,200mW or more optical output depending on current and lens used and individual diode efficiency. Typical current...

DANGER: APPROPRIATE LASER SAFETY GOGGLES MUST BE WORN WHEN OPERATING THIS DIODE! RISK OF INSTANTANEOUS SEVERE EYE DAMAGE OR BLINDNESS! A 5.6mm diameter 405nm wavelength BDR-S06J 12X diode identical to those used in the SL-VPB and PBAR parts bundles. These diodes can produce up to 650mW optical output or more depending on current and lens...

DANGER: APPROPRIATE LASER SAFETY GOGGLES MUST BE WORN WHEN OPERATING THIS DIODE! RISK OF INSTANTANEOUS SEVERE EYE DAMAGE OR BLINDNESS! This is a 660nm LPC-826 diode pressed into a standard diode module and includes a standard focusing ring (extended focusing ring optional). Typical output power is 300 +/- 25mW with a standard AR coated acrylic...

DANGER: APPROPRIATE LASER SAFETY GOGGLES MUST BE WORN WHEN OPERATING THIS MODULE! RISK OF INSTANTANEOUS SEVERE EYE DAMAGE OR BLINDNESS! No soldering required! This is a 445nm diode pressed into a standard diode module (copper module option available) and soldered to a 1.5A current regulated driver circuit that has been installed in a C6-style host...

DANGER: APPROPRIATE LASER SAFETY GOGGLES MUST BE WORN WHEN OPERATING THIS MODULE! RISK OF INSTANTANEOUS SEVERE EYE DAMAGE OR BLINDNESS! No soldering required! This is a 445nm diode pressed into a standard diode module (copper module option available) and soldered to a 1.25A current regulated driver circuit that has been installed in a C6-style...

DANGER: APPROPRIATE LASER SAFETY GOGGLES MUST BE WORN WHEN OPERATING THIS MODULE! RISK OF INSTANTANEOUS SEVERE EYE DAMAGE OR BLINDNESS! No soldering required!  This is a 660nm LPC-826 diode pressed into a standard diode module and soldered to a 520mA current regulated driver circuit that has been installed in a C6-style host "pill". Solder...

DANGER: APPROPRIATE LASER SAFETY GOGGLES MUST BE WORN WHEN OPERATING THIS MODULE! RISK OF INSTANTANEOUS SEVERE EYE DAMAGE OR BLINDNESS! No soldering required!  This is a 405nm BDR-S06J 12X diode pressed into a standard diode module and soldered to a 445mA current regulated driver circuit that has been installed in a C6-style host "pill". Solder...

The SL-DPMV includes a 445mA +/- 5% current regulated diode driver that has been soldered to a brass ring and pressed into a C6-style host "pill". Wires are silicone insulated. Each assembly is tested before shipment. Module is packaged in an anti-static bubble bag. This driver module is designed to be powered by two 3.7 volt rechargeable...

This product is identical to the driver module that is used in the P/N SL-LHA1 DIY 1-1.3W 445nm S4 Laser Host Assembly. The SL-DPM1 includes a 1.20-1.25A current regulated diode driver that has been soldered to a brass ring and pressed into a C6-style host "pill". Each assembly is tested before shipment. Module is packaged in an anti-static...

The SL-DPMR includes a 530mA +/- 5% current regulated diode driver that has been soldered to a brass ring and pressed into a C6-style host "pill". Wires are silicone insulated. Each assembly is tested before shipment. Module is packaged in an anti-static bubble bag. This driver module is designed to be powered by a single 3.7 volt 18650 battery....

A do-it-yourself (DIY) aluminum C6 host assembly that includes the retaining ring, heat sink holder, battery holder and tailcap switch, pill and brass ring. Does not include a heat sink, diode, diode driver, diode module, lens or other components. Accepts 2 X RCR123A, CR123A or 1 X 18650 batteries depending on diode and driver used. The C6 host...

This 9mm diameter 445nm AR coated glass lens assembly fits standard 12mm diode modules. This fully-threaded lens is coated specifically for the 445nm wavelength and will provide a slight increase in laser light output over other lenses that are coated for a wavelength range of 405-445nm.

This 9mm diameter 635-685nm AR coated acrylic lens assembly fits standard 12mm diode modules. This fully-threaded lens will provide an increase in light output over other uncoated acrylic lenses. Note: This lens is NOT the same as those found in standard AixiZ diode module assemblies.

MADE IN USA. Now includes our exclusive patent pending color anodized extended focusing ring in your choice of blue, red, violet, black or clear anodizing at no extra charge! This is the legendary "G-1" lens you may have heard about. These handmade single-element AR coated glass lens assemblies are significantly more efficient at light transmission...

Dual battery charger for rechargeable 3.7V 18650 batteries, with convenient flip-out wall plug built-in. Charger appearance may be slightly different than that shown.  Caution:  Do not recharge disposable batteries in this charger.

Dual battery charger for rechargeable 3.7V RCR123A batteries, with convenient flip-out wall plug built-in. Charger appearance may be slightly different than that shown. Caution: Do not recharge disposable batteries in this charger.

MADE IN USA. The battery extension tube allows the use of two "18650" Li-ion batteries with the Survival Laser S4 hosts for higher battery capacity, longer total run times and at full output power. This tube can also be used in other Aurora C6-style builds that normally use two CR123A or RCR123A batteries. However, DO NOT use this battery...

MADE IN USA. Céramique 2 is a high-density, ceramic-based thermal compound specifically designed for modern high-power CPUs and high-performance heatsinks. This compound may be applied between the diode module and heat sink, and between the heat sink and the host body for improved heat transfer during operation and potentially longer duty...

MADE IN USA. The extended length focusing ring is precision-machined from aircraft grade aluminum and is designed to fit standard 9mm diameter lens assemblies. It is nearly 1/2" long with a knurled outer surface and allows easier focusing without burning your fingers. The outside diameter is sized to fit commonly-used protective lens caps....

MADE IN USA. The extended length focusing ring is precision-machined from aircraft grade aluminum and is designed to fit standard 9mm diameter lens assemblies. It is nearly 1/2" long with a knurled outer surface and allows easier focusing without burning your fingers. The outside diameter is sized to fit commonly-used protective lens caps. A...

MADE IN USA. The extended length focusing ring is precision-machined from aircraft grade aluminum and is designed to fit standard 9mm diameter lens assemblies. It is nearly 1/2" long with a knurled outer surface and allows easier focusing without burning your fingers. The outside diameter is sized to fit commonly-used protective lens caps....

MADE IN USA. The extended length focusing ring is precision-machined from aircraft grade aluminum and is designed to fit standard 9mm diameter lens assemblies. It is nearly 1/2" long with a knurled outer surface and allows easier focusing without burning your fingers. The outside diameter is sized to fit commonly-used protective lens caps....

MADE IN USA. This must-have accessory is a stainless steel spring that goes around the outside of a standard lens housing and keeps the lens under tension against the diode module for more precise focusing. Easy to adjust and holds the lens position better than Teflon tape, which needs to be replaced periodically. This spring is sized for standard...

Universal clamp mount and tripod for holding any object less than 1.5" (3.8cm) in diameter. Holds laser approximately 6-7" above surface. Tripod legs are flexible and can be bent to virtually any position. Universal clamp mount can be removed and attached to larger tripods, tripod base can also hold small digital cameras and telescopes. Metal...

Pressure pad switch for remote activation of the 445nm assembled units based on the S4 and stainless steel hosts. Includes a coiled cord with a flat-sided pad for easy mounting. Use a small piece of self-adhesive Velcro (supplied) on the switch and mounting surface for removable applications. Multiple switches on the pressure pad allow for both...

A glow-in-the-dark (GITD) green silicone rubber lens cap identical to the lens caps shipped with the Survival Laser parts bundles. May also be used to replace the black tailcap switch cover.

Holster fits the Survival Laser and other Aurora C6-size hosts. Belt loop and 'D'-ring included.

Eagle Pair® brand protective laser safety goggles for combined 190-400nm & 580-760nm wavelengths. These goggles have 30% visible light transmission, protect to a level of OD 4+ (reduce the intensity of 190-400nm and 580-760nm laser light by a factor of 10,000 or more), and are CE certified. They are suitable for use with 190-400nm ultraviolet...

Update: Based on our testing with the recently-introduced high-power 635nm red diodes, these goggles appear to have an OD of approximately 2.5 at the 635nm wavelength. Eagle Pair® brand protective laser safety goggles for combined 190-470nm & 660-760nm wavelengths. These goggles have 40% visible light transmission, protect to a level...

Eagle Pair® brand protective laser safety goggles for combined 190-540nm & 800-2000nm wavelengths. These goggles have 20% visible light transmission, protect to a level of OD 4+ (reduce the intensity of 190-540nm and 800-2000nm laser light by a factor of 10,000 or more), and are CE certified. They are suitable for use with 405nm violet, 445nm...

Eagle Pair® brand protective laser safety goggles for combined 190-540nm & 900-1700nm wavelengths. These goggles have 30% visible light transmission, protect to a level of OD 4+ (reduce the intensity of 190-540nm and 900-1700nm laser light by a factor of 10,000 or more), and are CE certified. They are suitable for use with 405nm violet, 445nm...

Eagle Pair® brand protective laser safety goggles for 190-540nm wavelength, in a "slip over" frame style for individuals who wear corrective glasses. These goggles have exceptional visible light transmission (rated at 50%) and yet protect to a level of OD 4+ (reduce the intensity of 190-540nm laser light by a factor of 10,000 or more),...

Eagle Pair® brand protective laser safety goggles for 190-540nm wavelength. These goggles have exceptional visible light transmission (rated at 50%) and yet protect to a level of OD 4+ (reduce the intensity of 190-540nm laser light by a factor of 10,000 or more), and are CE certified. They are suitable for use with 405nm violet, 445nm blue, and...

A universal self-adhesive warning label that can be used with devices of virtually any wavelength and output power. Dimensions approximately 30x24mm.